iRig STOMP I/O Pedal Controller

SPECIFICATIONS

COMMON

• - Conversion: 24-bit A/D, 24-bit D/A
• - Sampling Rate: 44.1 kHz, 48 kHz, 88.2 kHz and 96 kHz
• - Power: USB bus powered (when used with a computer) or DC IN
• - Device Connection: USB B-Type and Mini-DIN
• - Enclosure: metal sheet

MICROPHONE INPUT

• - Connector: balanced female 3-pin XLR. Pin 2: hot / Pin 3: cold / Pin 1: ground
• - Microphone Input Level: from 6 mVpp to 1.4 Vpp
• - Microphone Input Impedance: approx 2 kOhms
• - Gain Range: approx 48 dB
• - Phantom Power: +48V ± 4V
• - Frequency Response: 20 Hz – 20kHz +/-1.5dB
• - Input Noise: -103 dB(A), -97 dB RMS

INSTRUMENT INPUT

• - Connector: unbalanced, Hi-Z, TS 1/4" Jack. Tip: signal / Shield: ground
• - Instrument Input Level: from 30mVpp to 6.9Vpp
• - Instrument Input Impedance: 1MOhms
• - Gain Range: approx 27dB
• - Frequency response: 20 Hz – 20kHz +/-1.5dB
• - Input Noise: -103 dB(A), -97 dB RMS

STEREO HEADPHONE OUTPUT

• - Connector: 1/8" TRS Jack. Tip: right / Ring: left / Shield: ground
• - Headphone Level control: numbered thumbwheel
• - Headphone Output Power: 100mW into 50Ohms

STEREO LINE OUTPUT

• - Connector: 2x balanced female 1/4" TRS Jack. Tip: hot / Ring: cold / Shield: ground
• - Maximum Output Level: +16 dBu into 600 Ohms balanced load
• - Output Impedance: 150 Ohms balanced
• - Floating Balanced Outputs

MIDI INPUT/OUTPUT

• - Connector: 2x 5-pin DIN

CONNECTIONS AND CONTROLS

• - Four metal foot-switches with one indication LED eachm dual color
• - Two analog potentiometer for Input Gain and output Volum
• - "Stomp Mode" LED
• - "Phantom 48V" LED
• - 4 segment s moni input level meter (peak)
• - 4 segment device putput meter
• - Continuous pedal (expression pedal) with virtual switch at the top fof its travel

REAR PANEL

• - Neutrik Combo socket for mIC input and instrument input (auto selecting)
• - +48V phantom power switch
• - 1/4" TRS Balance floating line outputs
• - MIDI I/O 5-pin DIN connectors
• - 2 x 1/4" TRS External controllers sockets
• - B-Type USB socket for connecting a computer (Mac/PC)
• - Mini-DIN "iPS" connector for connecting as iOS device
• - Barrel DC-in socket for powering up to Stomp I/O and charging the iOS device at the same time 

PACKAGING INCLUDES

• - iRig Stomp I/O
• - Lightning to Mini-DIN conenction cable with charging features (60cm/23.62")
• - USB A-Type to USB B-Type connection cable (2.5m/8.2ft)
• - DC power supply

DIMENSIONS

• - Size: 41.5cm/16.3" x 21cm/8.5" x 7.2cm/2.83"
• - Weight: 3.2kg/7.1lb
• - Lightning to Mini-DIN connection cable (60cm/23.62")
• - USB A-Type to USB B-Type connection cable (2.5m/8.2ft)

COMPATIBILITY

• iOS Devices
• Compatible with iPhone 8 Plus, iPhone 8, iPhone SE, iPhone 6s Plus, iPhone 6s, iPhone 6 Plus, iPhone 6, iPhone 5s, iPhone 5c, iPhone 5, iPod touch 6th generation, iPod touch 5th generation, iPad Pro (10.5-inch), iPad Pro (12.9-inch) 2nd generation, iPad Pro (12.9-inch) 1st generation, iPad Pro (9.7-inch), iPad mini 4, iPad Air 2, iPad mini 3, iPad Air, iPad mini 2, iPad mini, iPad 5th generation, iPad 4th generation. iOS 6 or later is required.